Waterjet cutting technology once again there is a new breakthrough, the laser applied to the waterjet cutting process, using water jet and laser mixing and cutting materials to obtain higher cutting quality. Compared with traditional cutting technology has the advantages:
1, Lower heat
Many people used laser cutting all know, laser cutting may result in very high quantity of heat, but this problem will not occur in conjunction with water jet this cold cutting device, in the waterjet cutting process, the cooling aspect play the absolute role.
2, High flatness
In the metal cutting process, the water jet can be easily separated the dissolving liquid produced after the metal dissolution, without causing the dissolving liquid solidification again and burr generated, greatly improve the flatness of the cutting.
3, Parallel side walls
During the cutting process, the workpiece is fixed in a CNC worktable, in the waterjet-guided laser beam toward one direction to move. Laser head move along with the vertical direction, only in order to comply with a variety of working interval with different nozzles under different water pressure, only the necessary to change the interval between the workpiece and worktable. It will not change during the cutting process.
Source: http://www.waterjetnozzles.com Waterjet Cutting Parts.
Sunday, September 6, 2015
Friday, September 4, 2015
Alternative use of waterjet cutting in life
Using water jet cleaning equipment stains, since waterjet has small cutting force area, high pressure, free of impurities and other characteristics, so the use of CNC equipment fixed the waterjet nozzle to the object plane, use the impact of water jet to remove some equipment hard attachments is also very effective, such as the use of water jet to clear ceramic coating, chemical pipeline fouling and so on.
The use of waterjet cutting all kinds of non-metallic materials such as paper, diapers, glass, fiber, sponges, etc.. Common water after the turbocharger pressurized, generate the 200MPa or less low pressure water jet, acting on an area less than 0.1mm, can be up to about 915 meters per second, can cut a large number of soft materials at one time.
Use water jet for patient to perform surgery, and now many of the world's medical researchers have successfully tested the surgeries using a water jet removed the liver, kidney and other organs. Although all of the medical equipment will be disinfected before use, but there is still the risk of surgical infections, and if used the pure water after rigorous disinfection to form a water jet for the surgery, then the risk of surgical infection can be greatly reduced.
Further water jet can also be used to dismantle the bomb, processed foods and so on usage, tools are dead but people are alive, take advantage of all the characteristics of waterjet to develop new uses for the waterjet cutting, may allow people to get the unexpected reward in the production and processing.
Source: http://www.waterjetnozzles.com Waterjet Cutting Nozzles.
The use of waterjet cutting all kinds of non-metallic materials such as paper, diapers, glass, fiber, sponges, etc.. Common water after the turbocharger pressurized, generate the 200MPa or less low pressure water jet, acting on an area less than 0.1mm, can be up to about 915 meters per second, can cut a large number of soft materials at one time.
Use water jet for patient to perform surgery, and now many of the world's medical researchers have successfully tested the surgeries using a water jet removed the liver, kidney and other organs. Although all of the medical equipment will be disinfected before use, but there is still the risk of surgical infections, and if used the pure water after rigorous disinfection to form a water jet for the surgery, then the risk of surgical infection can be greatly reduced.
Further water jet can also be used to dismantle the bomb, processed foods and so on usage, tools are dead but people are alive, take advantage of all the characteristics of waterjet to develop new uses for the waterjet cutting, may allow people to get the unexpected reward in the production and processing.
Source: http://www.waterjetnozzles.com Waterjet Cutting Nozzles.
Thursday, September 3, 2015
Abrasive Waterjet Cutting Tips
Waterjet cutting machine summed up the abrasive waterjet cutting techniques in the process of long time use.
1, Smaller abrasive particles (120 mesh abrasive or smaller) of the cutting speed is slower, but surface is smoother (compared with the 60 mesh and 80 mesh abrasive);
2, If you need to regularly punch a hole for composites, glass and stone, ensure that the system can use the controller to reduce or increase the water pressure. At the same time to check the vacuum assist device or other technologies to enhance these brittle material or laminated material perforation chance of success;
3, Compared with the general porous flow controller, specially designed for process control systems are generally more efficient and easier to use;
4, Typically inject the tap water into waterjet system, before the water is injected into the booster, usually we will filter out impurities in the water through the water filtration system, 90% of waterjet and abrasive waterjet users only require soften the water. Water filters will greatly extend the life of the water outlet, but also improve the life of the turbocharger wearing parts;
5, Underwater cutting will reduce the possibility of abrasive waterjet cutting top surface frost or "fogging". Underwater cutting also greatly reduces jet noise and confusion in the workplace. The only defect is the operator during the cutting process is not clear to see the jet, we can consider electronic performance monitoring devices. The monitoring device is able to detect deviations from optimum cutting performance, and can shut down the system before the component is damaged.
Source: http://www.waterjetnozzles.com Abrasive Waterjet Cutting Parts.
1, Smaller abrasive particles (120 mesh abrasive or smaller) of the cutting speed is slower, but surface is smoother (compared with the 60 mesh and 80 mesh abrasive);
2, If you need to regularly punch a hole for composites, glass and stone, ensure that the system can use the controller to reduce or increase the water pressure. At the same time to check the vacuum assist device or other technologies to enhance these brittle material or laminated material perforation chance of success;
3, Compared with the general porous flow controller, specially designed for process control systems are generally more efficient and easier to use;
4, Typically inject the tap water into waterjet system, before the water is injected into the booster, usually we will filter out impurities in the water through the water filtration system, 90% of waterjet and abrasive waterjet users only require soften the water. Water filters will greatly extend the life of the water outlet, but also improve the life of the turbocharger wearing parts;
5, Underwater cutting will reduce the possibility of abrasive waterjet cutting top surface frost or "fogging". Underwater cutting also greatly reduces jet noise and confusion in the workplace. The only defect is the operator during the cutting process is not clear to see the jet, we can consider electronic performance monitoring devices. The monitoring device is able to detect deviations from optimum cutting performance, and can shut down the system before the component is damaged.
Source: http://www.waterjetnozzles.com Abrasive Waterjet Cutting Parts.
Tuesday, September 1, 2015
To ensure the successful completion of waterjet cutting, we must carry out inspection work
When we using the waterjet cutting, due to the maintenance of the cutting head and delivery systems can not be guaranteed, it may cause more serious consequences. So when we conduct machining, to regularly check and maintain water jet cutting machine system to ensure its best optimal operating condition is conducive to the production. Specifically how to do it? Take the following steps.
First of all often open water at low pressure, to observe the gem nozzle flow situation. Normally, the water flow should be symmetrical, according to different types of nozzles, the width of the discharge water flow is not the same. General ruby and sapphire nozzle flow slightly wider, diamond nozzle flow is relatively narrow, and more coherent. If the water flow beginning wider, it means the nozzle is damaged, need to be replaced a new one, because if do not timely replacement of damaged nozzle, then it is likely to cause damage to the inside of the cutting head.
The second is to periodically check the cutting head whether has wear and tear phenomenon, sometimes some signs of damage caused by a number of factors that we are not easy to find, so be careful viewing. For example, after the sand tube accidental contact with the fixture, it will damage the nozzle nut of mixing tube to maintain the alignment and the internal parts.
Finally, sand delivery system consumable parts to regular inspection and replacement, such as pipes and fittings. To make sure any part of the sand transport system under the bottom of micro hopper is not exposed to the air. Specific operation of the first to disconnect the sand transfer line from the joint of micro hopper bottom, and then open the jet and the thumb stick in the end of the sand transfer line. Feel whether the sufficient amount of vacuum exists, because if the vacuum is insufficient, there may be cutting head entrance was blocked or sand delivery pipeline cracks, it should be resolved as soon as possible.
Through the layers of strict inspections to ensure the waterjet cutting machine processing smoothly, ensure the equipment parts in good condition, extending its service life.
Source: http://www.waterjetnozzles.com Waterjet Cutting Machine Parts.
First of all often open water at low pressure, to observe the gem nozzle flow situation. Normally, the water flow should be symmetrical, according to different types of nozzles, the width of the discharge water flow is not the same. General ruby and sapphire nozzle flow slightly wider, diamond nozzle flow is relatively narrow, and more coherent. If the water flow beginning wider, it means the nozzle is damaged, need to be replaced a new one, because if do not timely replacement of damaged nozzle, then it is likely to cause damage to the inside of the cutting head.
The second is to periodically check the cutting head whether has wear and tear phenomenon, sometimes some signs of damage caused by a number of factors that we are not easy to find, so be careful viewing. For example, after the sand tube accidental contact with the fixture, it will damage the nozzle nut of mixing tube to maintain the alignment and the internal parts.
Finally, sand delivery system consumable parts to regular inspection and replacement, such as pipes and fittings. To make sure any part of the sand transport system under the bottom of micro hopper is not exposed to the air. Specific operation of the first to disconnect the sand transfer line from the joint of micro hopper bottom, and then open the jet and the thumb stick in the end of the sand transfer line. Feel whether the sufficient amount of vacuum exists, because if the vacuum is insufficient, there may be cutting head entrance was blocked or sand delivery pipeline cracks, it should be resolved as soon as possible.
Through the layers of strict inspections to ensure the waterjet cutting machine processing smoothly, ensure the equipment parts in good condition, extending its service life.
Source: http://www.waterjetnozzles.com Waterjet Cutting Machine Parts.
Subscribe to:
Posts (Atom)